Commercial Plumbing, What You Need to Know

Excellent Plumber Rating

MPAQ Member
Fully insured and licensed

Google

Google Rating

Review stars
commercial plumbing

When it comes to plumbing, many would think that all kinds of plumbing services are all the same. In fact, they are not. Generally, types of plumbing services can be divided into two: residential plumbing and commercial plumbing. What are the differences between the two?

Commercial plumbing: what do they do?

Both commercial plumbing and residential plumbing work on the plumbing systems installed in a certain establishment. These include performing services and maintenance to water, sewer lines, water heater systems, and many plumbing related issues.

Unlike residential plumbing, however, commercial plumbing must also be supplemented with extensive knowledge of the building plans to be able to do a proper job, ranging from installation to regular maintenance. Therefore, their workload is also much more complex, as they have to deal with many elements and appliances related to the plumbing systems.

Commercial vs residential plumbing: The differences

what is commercial plumbing

Area and range of work

General rule of thumb is that commercial plumbing services are much broader in terms of the scope of their job and specializations. While residential plumbing services typically work on a smaller scale, such as low density settlements, commercial plumbing will tackle broader commercial establishments.

These include large buildings, such as apartments, hotels, malls, hospitals, office blocks, industrial areas, recreational parks, schools, restaurants, or generally big places which host many people in it. These establishments typically employ different, and as such larger and more complex plumbing systems which also results in a larger workload if compared to residential plumbing which usually works at residential houses at two or three floors maximum.

Different set of problems

As commercial plumbing tackles much larger establishments and more complex plumbing systems, as does the probability of various plumbing issues may arise, which typical residential plumbing may never have to deal with.

Proactive vs. reactive

Both commercial plumbing and residential plumbing work on repairing any arising problems involving such as damaged pipes and fixtures, faulty water heaters, and also inspection and maintenance. The difference is that since there are way many people in larger establishments, there are higher possibilities of their plumbing system getting worn out quicker and therefore commercial plumbing is often relied upon to make sure to prevent things from going wrong in the first place as it could be detrimental to business. Residential plumbing, on the other hand, is more reactive in nature and works whenever issues occur.

Types of tools

Common jobs require common tools. Yet, commercial plumbing requires more specialized tools to work as they have more workload to do. These include tools such as generators, industrial wet dry vacuums, tile saws, and extra cutting and drilling tools.

Working hours

Residential plumbing usually abides by local working hours. Commercial plumbing, however, may be required to work at any time whenever needed. This is because it is impossible for them to work while many people are still around. Commercial plumbing must be flexible since typically any types of work need to be done outside working hours. And since there are more people using the plumbing system, maintenance or repairing must be conducted more often.

Interdependent Work

Due to the scale of the job, commercial plumbing may need to work with many people from various expertises such as architects and engineers.

Commercial Plumbing 101

There are many services typical commercial plumbing may offer to their customer, but generally, these are the things which commonly found in commercial plumbing services:

  • Flexible working hours and available to hire at any time
  • Drain cleaning and maintenance to prevent clogging
  • Water and pipelines inspection
  • Pipes upgrade
  • Waste lines and vents check
  • Hot water systems maintenance
  • Leaks and blockages services
  • Water pressure check
  • Plumbing systems’ health and safety measures check
  • Regular maintenance schedule

Hiring Commercial Plumbing: What to Do

Make sure they fit what you’re looking for

If you decide to hire commercial plumbing, the first thing to do is to make sure what kinds of services they offer and how extensive they are. Regular or residential plumbing services are unlikely to do commercial plumbing jobs. See that what they do matches your job requirements during the consultation period.

Check their reputation history

Doing personal research beforehand can also prove to be helpful as it will give you a rough idea on the commercial plumbing services and how they do their past job. Does their rate match with the quality of their work? Do they always make sure to prioritize safety measures? What do other customers say about them?

Confirm their credentials

Lastly, remember that every plumber has a license before they are available to hire. Use an online service to check their license so you know their track records. After finishing the job, also make sure you keep a copy of the compliance certificate as insurance in case of future problems.

***

Platinum Plumbing is a licensed and insured plumbing company that has over 15 years of experience in the plumbing industry. We specialize in both residential and commercial plumbing solutions and are known for our cost-effective, reliable, and professional plumbing services.

If you are looking for proven and well-established plumbing services for your commercial or residential plumbing needs, Platinum Plumbing is the one to call. Contact us at 0741552828

no hot water

There is no feeling quite like finding out that your home has no hot water.

Just imagine this: we come home after work during a chilly night, wanting to quickly get into the bath but nope, suddenly things just simply don’t work. All you get from your shower faucet is that freezing, piercing, icy-cold water. There goes your plan of soaking yourself with a hot bath in a bathtub. Feels discouraging, no? Even more so when we don’t quite understand on how to deal with such a situation.

What causes the problem

All hot water systems typically work in a similar manner. Cold water runs through pipes, which are then heated up to set temperature and stored so that they are ready to be used on-demand. There are various types of water systems, such as continuous systems (typically powered by natural gas) and storage systems.

Each employs a different set of heating elements to work and problems may occur with these heating elements from time to time commonly due to wear, which will cause no hot water in your house.

No hot water? Do the initial check

When one encounters such a problem, the first and the foremost important thing to note is to make sure what kind of hot water system, as in the water heater, is used in the home. Generally, there are two kinds of water heaters: gas and electric water heaters. Both heaters involve a process of transforming a certain source of energy which allows cold water heated up to the desired temperature.

A gas water heater makes use of the law of physics where hot water always rises above cold water. Its gas burner is set to detect the proper temperature by a regulator, always heating up cold water below, allowing a constant supply of hot water which will then be delivered through a small pipe above a water tank.

An electric water heater, on the other hand, works by placing heating elements like rods, which are powered by electricity, inside the water tank. These rods are less corrosive, and so they are durable and will not contaminate the water. An electric water heater is seen as a more efficient option. Although, on the flip side, it costs a lot more compared to a gas water heater, especially if its power is constantly switched on.

Common problems for electric water heater

An electric water heater is prone to issues caused by sudden interruption to electricity. If it suddenly doesn’t work and you reckon that there is recently a power outage or blackout, you need to check whether the switch has tripped. Be wary not to touch any wires or terminals.

Another thing is to check the thermostat. There should be the upper and the lower thermostat. You need to confirm both settings are at the same temperature.

Also, you can check on the heating elements used in the tank and see whether they are working properly or need replacing.

Otherwise, as a common rule, all you might need is just simply switch your water heater off and on again.

Common problems for gas water heater

Confirm that the dip tube is not damaged. This dip tube works by making sure that cold water flows to the bottom of the tank which allows it to be heated. A faulty dip tube may otherwise direct it to the top, mixing with hot water, and reducing the temperature.

Check whether the pilot light is on or needs relighting. You may also see if the pilot light tube is clogged and needs replacement.

If you find that strong odour coming from the water, chances are the pilot light must be relit or there are issues with the gas line. The best thing to do here is to switch off your water heater and call professional help immediately.

Other things to check

Sometimes your water heater may make sizzling sounds, which in this case shows signs of leaking somewhere. Leaks may occur in many places, such as valves which can be repaired by tightening them or replacing the joint. But if leaks are caused by corrosion in the tank, you need to consider immediate replacement.

You may also experience low water pressure. First confirm if the low pressure applies to either cold or hot water, or both. You need to make sure that the shutoff valve in your house is fully open.

The color of the water is also a sign of whether your water heater is working properly or not. A change in color is a sign that bacteria are growing inside the tank. Sometimes you only need to replace an anode rod, but the water tank may also show visible corrosion which needs replacement as soon as possible.

All done, what to do next?

If you have finished some of the checklists above and still no sign of change, there might be problems somewhere else. At times they will also prove to be a lot more serious and may even cause harm. When it comes to this, better leave it for the professionals to do the repair. Call the best plumbing services available nearest to you.

Platinum Plumbing is a licensed and insured plumbing company with more than 15 years of experience in this industry. We are the plumber Bundaberg that provides various plumbing services including blocked drains, hot water systems, leaking/bursting pipe repairs, and many more.

If you need a proven, well-established plumbing company for your hot water system, Platinum Plumbing is the plumbing company to call. call us at 0741552828

There is hardly any person who hasn’t heard the adage that water is life. Yes, water is extremely precious to sustain life and this reality is executed by the system of residential plumbing. This mechanism involves every corner of your house that uses water. It can include sinks, bathtubs, taps, showers, etc. The simplest answer to what is residential plumbing is that it is the system that provides your house with water. This is one of the most complicated and pricey installations that your house has and thus you should understand its design, purpose, working, and maintenance.

What are the objectives and features of a good residential plumbing system?

Any good residential plumbing system should first be able to supply enough sanitary drinking water whenever required. The pipeline should be made in such a way so that there is no leakage of water. Besides this, the pipeline should channel wastewater safely out of the residence. Drainpipes in residential plumbing should be connected to septic and sewer lines for this purpose. Lastly, the plumbing must be of good quality and must not emit any foul gasses into the home.

What happens if your residential plumbing system undergoes damage and leak?

Since these systems are used all the time, a certain level of wear and tear is expected. In such a case, where a pipeline is leaking, you should immediately call for professional help or a plumber to fix it as soon as possible. That said, you can potentially avoid any such leaking mishap in your house if you inspect your residential plumbing system regularly.

Now the natural course of thought will lead anyone into asking, what exactly happens during a plumbing inspection? Here’s what happens:

  • To call a plumbing inspector, you must call the service provider and book an appointment describing the service you need. The professional plumber will take a look at the plumbing around your home to determine any damage or suspicious areas that can give you trouble in the future.
  • The professional will essentially be walking through your house and checking for leaks and dripping. They will inspect with an expert’s eye such that the spot on the wall that looked normal to you could turn out to be a leaking pipe.
  • Once the damaged areas have been identified, they will photograph the areas and let you know about the next course of action, i.e, how they will fix it, the time it will take, and the cost.
  • The cost will depend on the extent of the damage.

You can avoid any major plumbing disaster in your home by making sure to get your plumbing line inspected every once in a while. However, if you do end up with a leaking pipe that needs to be fixed as soon as possible, and if you are looking for a plumber Bundaberg, then Platinum plumbing Bundy is your best shot out of this. Try to limit the leak by tying a cloth around it and calling them as fast as you can!

How to clear a blocked toilet

A blocked or clogged toilet has got to be one of the most annoying things that can happen. Most of the time when one flushes down things into the toilet that should not be flushed down, it results in a clogged toilet. Solid objects, polythene, or even bundled toilet paper can block your toilet and cause all the water to pour out of it.

If your toilet keeps getting clogged then it can be quite frustrating if not disgusting and you might need to resolve it as soon as possible. Strictly speaking, you can unclog a toilet by yourself but a professional plumber will be able to identify the underlying issue about why your toilet keeps getting clogged.

Now you may be wondering about how to clear a blocked toilet. There are many techniques you can follow. The most effective of them have been compiled for you.

Using A Plunger

It is the most sought way to unclog a toilet. Gently use the plunger to seal the opening at the bottom of the toilet sink and push it down slowly. Once the plunger is held tight by the vacuum created, bring it up and down in a to and fro motion until the debris stuck on the other side is flushed out.

Use Packing Tape

If you don’t have a plunger, seal the open mouth of the toilet sink with packing tape and then flush the toilet. When the air comes up, the tape will start to rise and you will have to push the air down along with the tape. The compressed air will do the trick.

With Vinegar and Baking Soda

Throw a fistful of baking soda into the toilet and wait for two minutes. Then slowly pour about two cups of vinegar into the same place. The mixture will create bubbles and fizz. Repeat the process and flush until the clog is gone.

Hot Water and Dish Soap

Hot water and dish soap also may work when the clogging is minimal. For this, to work you have to pour generous amounts of dish soap into the toilet sink and then pour boiling and bubbling water over it very slowly. Be careful about not getting splashed with hot water because it may cause blisters.

Use A Toilet Cleaner

If nothing else works, those are made of harsh chemicals that dissolve the clogging agent. Make sure to ventilate your washroom properly and do not inhale the fumes.

Those are some of the most effective ways to clear a blocked toilet by yourself. But as already mentioned, if this keeps happening then the problem may be elsewhere. It can be a clogged toilet vent or blocked toilet drain that may be causing the problem. These you cannot solve without professional help.

Call A Professional Plumber

So if you are looking for a plumber Bundaberg then call an expert from Platinum plumbing Bundy as the solution to all your plumbing-related problems. It is best to leave critical issues to an expert because it may backfire and cause more damage than was originally the case.

For most homeowners like you and us, any problem with the hot water system goes unnoticed unless there is the unavailability of hot water at all. Minor issues are rarely looked into and water leaks can go on unnoticed for weeks at a length. However small the leak is, chances are it will ruin your floor, the wall, and other furniture near the area of the leak. And do not forget the damages it does to your water heating system. It is prudent to fix any leaks in the pipes or in the tank of your water system and check regularly for any signs of distress to the entire apparatus. Here are a few reasons that can answer if you are wondering why is my hot water system leaking?

What Can Cause A Leak In The System?

For any hot water installation which is regularly used, there are multiple factors that can result in a leak. It could be because of a faulty relief valve, the leak could be made due to a damaged tank or the pipes and connectors are coming loose over the years. Given ahead are a few major factors that cause a leak in a typical hot water system:

1. Pressure Relief Valve

The PRV works by releasing a little pressure periodically so that the whole system remains under the levels of mechanical stress it can bear. But due to dirt or grit in the water, the PRV can experience loose seals and damages. If you observe a puddle under the PRV, it should be replaced immediately.

2. Water Pressure

It so happens that many of us stay in apartments that have water pressure that is higher than the standard operating limits of the heating system. This means the extra pressure can force the water to leak from inside the system. You need to check and maintain the right pressure inside the system and keep regularly checking the gauges.

3. Loose Fittings

This is as easy to occur as it is to repair. Over time, your pipes and fittings will experience wear and tear and fatigue due to constant expansion and contraction caused by hot water. This makes the fittings and washers lose. It results in the water finding places to leak from the pipes.

4. Tank Damage

Cracks, fractures, fissures, and holes begin to develop in your water tanks due to corrosion. If there is an unusual level of water loss in your hot water system, the chances of it leaking from your water tank are high. Whether you like it or not, a metal tank always starts to corrode hence it is important to keep checking the tank for points of failure.

What to Do?

1. Identify

Find the source of the leak. It is important to know where the leak is coming from, the top of the tank or the bottom of it as it can affect the cost and type of repair. A leak from the top of the tank is typically much easier to repair than one from the bottom.

A bottom leak typically indicates an issue within the tank itself. It can accumulate residue inside over time, which can cause the tank to leak. If this is the source of the leak, you should consider to replace the unit. Check the water volume coming out of the pressure release valve if the leak is coming from it. It’s normal for water to leak from the pressure release valve, However, if the leak causes a puddle or a bucketful of water, the valve should be replaced.

If the leak is coming from the tank’s top, it could be caused by a faulty anode rod, a loose pipe, or a leaking cold water pipe valve. If the cause is a faulty anode rod, you should contact your hot water experts as soon as possible to have it checked because it can lead to more serious problems.

2. Turn Off Water Supply

Turn the water supply off once you’ve determined the location of the leak. This can be done directly at your hot water system or throughout the house. The water connection pipe, which is usually attached to the bottom of the system, should have a control dial that allows you to turn off the water supply that goes directly to the system. If you are unable to do so, you must turn the main water supply off. Although this may appear to be inconvenient, preventing water from entering the leaking system is critical to minimizing any water damage, potentially saving you a lot of time and money

3. Call A Professional Plumber

The degree of water flowing out of the system determines how big or small the issue is. If you are able to catch it early on, it is a better situation to be. Being late in fixing the hot water system can result in the whole system needing repairs instead of a single part. Hence, it is essential to get in touch with a plumber Bundaberg who can at least provide you with a professional opinion before you begin tinkering with the system on your own.

The best way to handle a leaking hot water supply system is to let the professionals do the job. It is not so much the water but the electric supply or the fuel supply that you need the protection from. If you own an electric system, you need to be extra careful because water and electricity are not a good combination. A leaking system should however not raise any major alarm bells. It is essential that the problem is addressed quickly and with some professional help.

When it comes to taking care of pipes and plumbing in the region, Platinum Plumbing Bundy is your best bet against all the water woes. So whether it is the leaking pipe or it is the tank; whether it is the valve not working or it is an issue with the main supply, a professional plumbing service can effectively deal with all your problems. Remember, in case of a leak, just switch off the water mains and let the professionals do their magic.

Don’t you hate it when a tap in your house keeps leaking? The constant dripping noise and the realization that something is faulty in your home, are highly frustrating. Not only this, did you know that a typical leaking tap can result in the loss of more than ten thousand liters of water in a year? If the noise and extra effort that goes into closing the tap every time doesn’t bother you, then the loss of water should. Fixing a leak is super easy. Do you wonder how to fix a leaking tap? are you interested in knowing the steps involved in the process? In that case, we have got you covered.


The preparation needed to fix the tap


Before you can begin fixing your tap, you need to dismantle it. Now dismantling a tap entails exposing the pipe that brings water into the tap. Hence, stop the water flowing into the pipe before you start dismantling the tap. Usually, closing the main valve or a secondary valve that regulates the flow of water around the house or into the specific area of your house will do the trick. You can find the water mains outside the house in your front yard or in the bathroom itself if you live in an apartment. You will need to turn on the tap to release any residual water in the system before you begin working on the leak.


Another thing to note is covering any points of drainage that are around the tap you are fixing. You might be repairing the tap in the kitchen sink or the one in your shower. You should cover the drainage to prevent any small parts from falling into the drainage if you accidentally drop them as you work.


You also need certain parts that will enable you to fix the leaking tap:
• Single ½” washer
O-rings
• Jumper valve
• Spanner/Wrench
• Screwdriver
• Tap lubricant
• Piece of cloth

What are the steps to repair the tap?


Now that you are well prepared, let us see how can you fix the leak in 5 steps:

  1. Use the spanner to remove the cover on the top of the tap. This will reveal a screw. You can find this under the hot /cold sign on the tap.
  2. Use the screwdriver to undo the screw and then remove the handle of the tap.
  3. Remove the headgear to reveal the jumper valve. Remove the washer and the O-ring carefully to free the jumper valve. Check if the washer and the O-ring are old or cut due to wear and tear.
  4. Next replace the jumper valve, the washer and O-ring with new parts. Use the lubricant on the spindle for smooth tap operation.
  5. Refit the headgear and spindle after putting the new jumper valve in place. Just be careful that you do not over-tighten the screws and nuts. This should complete the repair job.

By following these five simple steps you can turn any old tap as good as new. There is one thing that you need to ensure. The headgear, the jumper valve, and spindle should be tightly sealed to avoid leakage of water. You can use a plumber’s putty or a thread to provide extra firmness to all the elements. No matter what kind of tap you have in your house, the innards remain the same. It is only the design of the headgear that changes. Hence these steps will help you repair all sorts of taps.


Sometimes, you need re-seating of the tap to repair it. In case, even after following the steps mentioned above the leak is not repaired, you will need the help of a plumber. A professional plumber Bundaberg from Platinum Plumbing Bundy is the answer for all kinds of problems you might experience with your plumbing in general or taps in particular. It is crucial to take the opinion of professionals if you cannot fix the plumbing on your own. To prevent issues from aggravating, always hire professional plumbers. A leak in your tap might not seem like a big issue but if you don’t take proper care and resolve it correctly, it might end up costing you more than it should.

There are those who tackle the problems as and when they come and there are those who need to be prepared for emergencies to tackle difficult situations efficiently. In case of plumbing, however, it is always beneficial to be in the latter category. On average, a homeowner will be faced with at least one emergency plumbing situation every year and as the house gets older, the cases may rise. In order to keep yourself prepared to handle small plumbing needs and emergencies, a home should have a kit that has the right tools to help navigate the problem with ease

There are tools for every problem you face and a professional plumber would carry at least 25-30 tools excluding the variants of each with themselves. However, if you are not a plumber then it is illogical for you to have so many tools lying around just for plumbing. The right mix of tools will take care of most of the worries.

The minimum plumbing tools one should keep in the house

Being prepared does not mean one needs a full garage of tools. Having 5 or six tools in your garage will help you overcome most cases and manage extreme cases till professionals arrive. All you need is a bag and the following tools

  • Plunger – Used to clear clogs in your drain. The easiest method to clear blocked drainage is to fix the plunger and go for it. Whether it is your shower, sink or toilet, you can use the plunger to clear things up easily
  • Wrench – This is one tool that plumbers cannot do without. If you see someone holding this tool, chances are they are a plumber. Wenches do come in a lot of shapes and sizes but a basic wrench with adjustable mouth is all you need for your home kit.
  • Pliers – When it comes to tightening or loosening nuts and bolts that are hard to reach, the pliers can come in very handy. It is also used to hold one end for grip and tighten the other using the wrench.
  • Putty – If you are looking to replace or remove a fixture then putty will help you achieve the best fit for your fixture. It remains soft even when used for longer durations and does not work like an adhesive hence is easier to remove.
  • Sealing Tape / Sealant – Most of the time when there is a crack in the pipes or a hole that seeps, all you need to do is put a sealant on top of it. This prevents any further water damage to the area and you can gain some time before the plumber arrives to help you fix the problem.

The following tool kit will be a bare minimum starter pack for you to be able to deal with the leaking tap, clogged drains, or any such minor plumbing issues and emergencies that you will have to face. It will help you prevent further damage before the professionals arrive and take charge of the situation.

A blocked drain is not only a plumbing problem, but it causes a lot of inconvenience and damage like foul smell, damage to furniture and interiors. That is why it is important to ensure that blocked drains are fixed immediately and we try and prevent this issue before it occurs. As a homeowner, it will help if you have some basic knowledge of potential issues, you can do the first-level diagnosis and then take the help of professional plumbing services to fix the drain.

How to identify a blocked drain?

The signs of a blocked drain can creep up over time at a slow pace and if left unchecked will become a major issue. The following red flags are easy to spot and can help you identify a blocked drain:

  1. A foul smell emanating from the sink or a drain hole indicates that some household matter like food and paper has blocked the drain and is decomposing to cause the bad smell.
  2. An overflowing toilet bowl could point toward a blocked outdoor drain or manhole.
  3. Gurgling sound in the flush or the drains indicates trapped air. This can help you spot the exact point of blockage as the sound is generated when water tries to flow around a blockage.
  4. Slow drainage is a very prominent sign of a block in the drain. If you see slow drainage in sink, shower or the toilet bowl there is a surely a blockage obstructing the water flow.

Easy tips to clear blocked drains

Here are some easy tips you can use to clear minor clogs in the drain.

  • Boiling water is a simple and non-toxic option to clean blocked sink, drain or toilet bowls. Boiling water will break down grease, food and soap that might be causing the blockage. If you have PVC pipes, you must choose hot water rather than boiling water.
  • A combination of baking soda and white vinegar is a great household solution and a natural drain cleaner. After using this solution, you should flush the drain with hot water to remove any remnants.
  • Cup plungers are simple and practical non-chemical ways to unclog drains. A plunger helps create air based force that can shift any object that is causing the obstruction.
  • Caustic cleaners are commonly used for tough to handle clogs, however, these are not very environment friendly and hence must be used carefully. You must wear a mask and gloves while using these cleaners.
  • A severe blockage which cannot be unblocked with these simple measures will need professional intervention. A plumber might need to dig the area around the pipe, remove blockages and repair the damage.
  • High pressure water jets can resolve some of the toughest blockages. However, these need to be operated by professional plumbers as the force is very strong. This is commonly used when tree roots are blocking the main drains.

If you think the blockage is not so tough can be resolved with one of the DIY tips you should try that, in case of a large-scale property or a tough block you must call for a commercial plumbing service.

Sooner or later, your taps may start to malfunction and exhibit one or more problems. The problems may be minor, but occasionally, they may point towards a more serious underlying issue with your plumbing. In this post, we’ll take a look at the most common tap issues that plague property owners in Bundaberg.

Before we start looking at the problems in detail, we’d like to state right off the bat that whenever you experience any plumbing issues, you should immediately contact professional plumbing services. Going the DIY way may harm more than help, which can end up costing you a lot of money to fix. So, with that being said, let’s get back into the groove of things and take a closer look at all the common tap troubles along with their solutions.

1. Leaky or Dripping Taps

A drippy or leaking tap may indicate a problem with its washer or seal. Faulty washers or seals are typically encountered with independent cold and hot taps. In such a scenario, the best thing to do would be to very cautiously remove the washer and/or seal and have the faulty components replaced by a professional plumber in Bundaberg.

If you’re unsure about removing the washers and/or installing them, don’t take an unnecessary risk in trying to do everything on your own, as you may end up damaging other components that are working just fine. If you detect the drip or leak in a bathroom mixer tap, the problem may lie in the ceramic cartridge that stays within the tap. Replacing the cartridge is as easy as replacing the washers and seals of separate cold and hot taps.

2. Reduced Water Pressure

When water pressure goes down, the flow of water is severely affected. This comes to the surface when you turn a tap open. A change in water pressure doesn’t necessarily mean that there’s something wrong with your tap. It could very well be a problem with the external water mains or a half-open stop valve. It may also be triggered by multiple water systems running simultaneously.

It’s best to ask a reputed plumbing professional to pay you a visit to figure out what exactly is affecting the water pressure. If it is indeed a tap issue, it’s most likely due to locked air inside the pipes connected to your tap.

3. Limescale Deposit Build-up

Property owners residing in places with hard water often complain of built-up limescale deposits on their plumbing. While a little build-up isn’t really a great cause for concern, over time, a little may end up becoming a lot, and that is a problem. If the limescale deposits aren’t cleaned from time to time, they can severely restrict water flow and reduce the efficiency of your plumbing

Dealing with limescale deposits is something that you can do on your own. Simply get a branded cleaning product meant for removing limescale deposits or use vinegar or lemon juice to loosen the deposits. Once the deposits are loosened up and broken down, scrub them off.

So, the next time you encounter one of these common tap troubles, you’ll know what to do, won’t you?

It’s easy for drainage problems to go completely unnoticed, especially in their early days. Most of them develop very slowly over time, and their development is helped by the fact that drains stay underground. However, once one or more of those problems begin to surface, the situation can become overwhelming in a short span of time.

In this post, we’d like to take you through three of the most common yet dreaded drainage problems faced by property owners in Bundaberg – problems that need professional plumbing services to be dealt with. So, without further ado, let’s get right into it!

1. Displaced Pipe Joints

Ground movement is a natural phenomenon but it is often exacerbated by an increase in traffic levels or a sudden rise in construction activities in the vicinity. Over time, this movement can potentially displace the pipe joints and create openings for wastewater to leak out of. This problem may not be evident initially as the effects of the leaking wastewater will take time to come to the fore. But when it does become apparent, it can potentially cause structural damage to not just your plumbing, but your property as well.

Identifying and dealing with displaced or open pipe joints is best left to the professionals, who employ a process known as drain relining to solve the issue. If the displacement is minor, patch lining is used to repair the damage.

2. Root Rage

The roots of plants and trees grow downwards as they look for more nutrients in the soil along with oxygen and water, and your sewer system is a rich source of nutrients needed by them. All it takes for a root to penetrate the drain pipes is a small opening, and if the penetration occurs, it may lead to further openings and holes in the pipes. And as a result, wastewater will rapidly leak out, once again posing the risk of structural damage. Even if the penetration doesn’t result in significant wastewater leakage, a growing root system within the drain pipes can cause blocked drains.

Dealing with this root rage is no easy feat. DIY methods include using copper sulphate to get the roots out of the way. However, instead of risking further damage to your drainage, you should get in touch with the professionals who use techniques like drain jetting and high-pressure flushing to remove roots.

3. Debris Build-up

From coffee grinds to hair and more – all sorts of debris may accumulate inside your drain pipes over the years. The thicker the debris is, the greater the chances are of it causing a blockage within the drainage system. As a blockage becomes more significant, it slowly reduces the efficiency of the drainage system until it completely collapses, resulting in pipes breaking apart and all the accumulated debris and wastewater flowing out.

It’s not recommended to go down the DIY route when it comes to unblocking your drain pipes. If you notice your drainage becoming more inefficient with each passing day, contact a professional. A licensed plumber Bundaberg conducts CCTV drain surveys to identify the type of debris that’s causing the blockage. Once the cause is identified, the professional work out a meticulous plan for getting things back in order.

It’s best to schedule CCTV drain surveys a few times every year to ensure the health of the drainage systems in your property. After all, the quicker a pro manages to identify the problem, the faster it gets resolved.